VHF and UHF antennas - Revision history

Elijah: /* 900 antenna */

2024-08-15T20:57:00Z

900 antenna

← Older revision		Revision as of 20:57, 15 August 2024
Line 18:		Line 18:
	==900 antenna==		==900 antenna==
	I made this to get on the 900 Mhz ham band. Simple antenna to build from an "N" chassis mount connector. I have it sitting on top a 3/4 PVC pipe which is attached to the eaves of my roof.		I made this to get on the 900 Mhz ham band. Simple antenna to build from an "N" chassis mount connector. I have it sitting on top a 3/4 PVC pipe which is attached to the eaves of my roof.
	[[File:900mhz_antenna.jpg\|thumb\|~~NanoVNA showing return loss~~]]		[[File:900mhz_antenna.jpg\|thumb\|Simple 900 Mhz Vertical]]

	<br clear=all>		<br clear=all>

	==1090 antenna==		==1090 antenna==
	Not strictly ham radio, but 1090 is the frequency aircraft use to reply to ground based radar (mode A/C) as well as "extended squitter" mode S, usually carrying ADSB data. This particular antenna is used in one of my gliders to receive ADSB on PowerFLARM for collision avoidance. It's a dipole antenna and while a dipole is a poor match to a 50 ohm unbalanced feed, it's good enough to pick up aircraft within the range you care about. ADSB signals are broadcast with quite a bit of power so even a marginal antenna will pick them up from quite a distance.		Not strictly ham radio, but 1090 is the frequency aircraft use to reply to ground based radar (mode A/C) as well as "extended squitter" mode S, usually carrying ADSB data. This particular antenna is used in one of my gliders to receive ADSB on PowerFLARM for collision avoidance. It's a dipole antenna and while a dipole is a poor match to a 50 ohm unbalanced feed, it's good enough to pick up aircraft within the range you care about. ADSB signals are broadcast with quite a bit of power so even a marginal antenna will pick them up from quite a distance.

Elijah at 06:05, 13 August 2024

2024-08-13T06:05:54Z

← Older revision		Revision as of 06:05, 13 August 2024
Line 14:		Line 14:

	[[File:PXL_20221207_202053670.jpg\|thumb\|CheapYagi on my roof]]		[[File:PXL_20221207_202053670.jpg\|thumb\|CheapYagi on my roof]]

			<br clear=all>
			==900 antenna==
			I made this to get on the 900 Mhz ham band. Simple antenna to build from an "N" chassis mount connector. I have it sitting on top a 3/4 PVC pipe which is attached to the eaves of my roof.
			[[File:900mhz_antenna.jpg\|thumb\|NanoVNA showing return loss]]

	<br clear=all>		<br clear=all>

Elijah at 06:38, 25 February 2024

2024-02-25T06:38:35Z

← Older revision		Revision as of 06:38, 25 February 2024
Line 14:		Line 14:

	[[File:PXL_20221207_202053670.jpg\|thumb\|CheapYagi on my roof]]		[[File:PXL_20221207_202053670.jpg\|thumb\|CheapYagi on my roof]]

			<br clear=all>
			==1090 antenna==
			Not strictly ham radio, but 1090 is the frequency aircraft use to reply to ground based radar (mode A/C) as well as "extended squitter" mode S, usually carrying ADSB data. This particular antenna is used in one of my gliders to receive ADSB on PowerFLARM for collision avoidance. It's a dipole antenna and while a dipole is a poor match to a 50 ohm unbalanced feed, it's good enough to pick up aircraft within the range you care about. ADSB signals are broadcast with quite a bit of power so even a marginal antenna will pick them up from quite a distance.

			[[File:1090_antenna.jpg\|thumb\|NanoVNA showing return loss]]

			The NanoVNA is a great tool for cutting antennas to length. Calculate the lengths to get it close, then trim as needed to nail the resonant point. I think these are so cool - so much functionality for so cheap! Obviously they don't have the dynamic range of a more expensive VNA but it's plenty good enough for a lot of projects.

			[[File:1090_ant_return_loss.jpg\|thumb\|NanoVNA showing return loss]]

Elijah at 23:58, 5 December 2023

2023-12-05T23:58:26Z

← Older revision		Revision as of 23:58, 5 December 2023
Line 3:		Line 3:
	If you want a simple omni-directional antenna, it's hard to beat a vertical. Advantageous over a dipole for focusing the signal more toward the horizon, they are simple to build and are usually sufficient for most vhf/uhf needs. There are lots of sites on the internet telling you how to calculate the length of the elements so I won't duplicate that here. My technique is to start with a quarter wavelength for the frequency you want, then connect an antenna analyzer (or in recent years, a nano-VNA) and trim until it resonates where you like.		If you want a simple omni-directional antenna, it's hard to beat a vertical. Advantageous over a dipole for focusing the signal more toward the horizon, they are simple to build and are usually sufficient for most vhf/uhf needs. There are lots of sites on the internet telling you how to calculate the length of the elements so I won't duplicate that here. My technique is to start with a quarter wavelength for the frequency you want, then connect an antenna analyzer (or in recent years, a nano-VNA) and trim until it resonates where you like.

	[[File:Diy_vertical_antenna.jpg\|~~400px~~\|A robust vertical antenna]]		[[File:Diy_vertical_antenna.jpg\|thumb\|A robust vertical antenna]]

	Here's a design I came up with recently. It uses a chassis mount SO-239 connector with the elements soldered directly on. First I solder on the vertical element, then I solder on a piece of 1/2 copper pipe to go around it as a strain relief. Then solder/bolt on the radials. At the end, I fill the copper pipe up with epoxy. This gives a nice strain relief and has proven quite robust out in the elements. BTW it is important to at least paint the epoxy to protect it from UV.		Here's a design I came up with recently. It uses a chassis mount SO-239 connector with the elements soldered directly on. First I solder on the vertical element, then I solder on a piece of 1/2 copper pipe to go around it as a strain relief. Then solder/bolt on the radials. At the end, I fill the copper pipe up with epoxy. This gives a nice strain relief and has proven quite robust out in the elements. BTW it is important to at least paint the epoxy to protect it from UV.

			<br clear=all>
	==DIY Yagi antennas==		==DIY Yagi antennas==
	I ran across this design and I think it's really clever - a yagi with no gamma/hairpin match needed. It's designed for simple and quick construction. I've had it up for a couple years and it's worked really well. He has a couple excellent articles on this, search the following link for "Cheap yagi"		I ran across this design and I think it's really clever - a yagi with no gamma/hairpin match needed. It's designed for simple and quick construction. I've had it up for a couple years and it's worked really well. He has a couple excellent articles on this, search the following link for "Cheap yagi"
Line 12:		Line 13:
	https://www.wa5vjb.com/references.html		https://www.wa5vjb.com/references.html

	[[File:PXL_20221207_202053670.jpg\|~~400px~~\|CheapYagi on my roof]]		[[File:PXL_20221207_202053670.jpg\|thumb\|CheapYagi on my roof]]

Elijah at 23:25, 5 December 2023

2023-12-05T23:25:19Z

← Older revision		Revision as of 23:25, 5 December 2023
Line 6:		Line 6:

	Here's a design I came up with recently. It uses a chassis mount SO-239 connector with the elements soldered directly on. First I solder on the vertical element, then I solder on a piece of 1/2 copper pipe to go around it as a strain relief. Then solder/bolt on the radials. At the end, I fill the copper pipe up with epoxy. This gives a nice strain relief and has proven quite robust out in the elements. BTW it is important to at least paint the epoxy to protect it from UV.		Here's a design I came up with recently. It uses a chassis mount SO-239 connector with the elements soldered directly on. First I solder on the vertical element, then I solder on a piece of 1/2 copper pipe to go around it as a strain relief. Then solder/bolt on the radials. At the end, I fill the copper pipe up with epoxy. This gives a nice strain relief and has proven quite robust out in the elements. BTW it is important to at least paint the epoxy to protect it from UV.

			==DIY Yagi antennas==
			I ran across this design and I think it's really clever - a yagi with no gamma/hairpin match needed. It's designed for simple and quick construction. I've had it up for a couple years and it's worked really well. He has a couple excellent articles on this, search the following link for "Cheap yagi"

			https://www.wa5vjb.com/references.html

			[[File:PXL_20221207_202053670.jpg\|400px\|CheapYagi on my roof]]

Elijah: Created page with "Category: Ham Radio ==DIY Vertical antennas== If you want a simple omni-directional antenna, it's hard to beat a vertical. Advantageous over a dipole for focusing the sign..."

2023-12-05T01:12:36Z

Created page with "Category: Ham Radio ==DIY Vertical antennas== If you want a simple omni-directional antenna, it's hard to beat a vertical. Advantageous over a dipole for focusing the sign..."

New page

[[Category: Ham Radio]]
==DIY Vertical antennas==
If you want a simple omni-directional antenna, it's hard to beat a vertical. Advantageous over a dipole for focusing the signal more toward the horizon, they are simple to build and are usually sufficient for most vhf/uhf needs. There are lots of sites on the internet telling you how to calculate the length of the elements so I won't duplicate that here. My technique is to start with a quarter wavelength for the frequency you want, then connect an antenna analyzer (or in recent years, a nano-VNA) and trim until it resonates where you like.

[[File:Diy_vertical_antenna.jpg|400px|A robust vertical antenna]]

Here's a design I came up with recently. It uses a chassis mount SO-239 connector with the elements soldered directly on. First I solder on the vertical element, then I solder on a piece of 1/2 copper pipe to go around it as a strain relief. Then solder/bolt on the radials. At the end, I fill the copper pipe up with epoxy. This gives a nice strain relief and has proven quite robust out in the elements. BTW it is important to at least paint the epoxy to protect it from UV.